Search results for "internal combustion engine"
showing 10 items of 36 documents
Vibration reduction on city buses: Determination of optimal position of engine mounts
2010
International audience; This study is composed of three essential parts. The first part describes an indirect semi-experimental method which is used to reconstruct the excitation force of an operating diesel engine from the acceleration data measured at the mounting points. These internal forces can not be directly measured with force sensors; they have to be derived from the dynamic deformation of the engine support, so a theoretical analysis is carried out to derive the equations for the force re-construction.The second part deals with prevention of low frequency vibration of the powertrain from spreading to the rest of the vehicle. Three uncoupling techniques are used to minimize these v…
DETERMINATION OF TDC IN INTERNAL COMBUSTION ENGINES BY A NEWLY DEVELOPED THERMODYNAMIC APPROACH
2010
Abstract In-cylinder pressure analysis is nowadays an indispensable tool in internal combustion engine research & development. It allows the measure of some important performance related parameters, such as indicated mean effective pressure (IMEP), mean friction pressure, indicated fuel consumption, heat release rate, mass fraction burned, etc. Moreover, future automotive engine will probably be equipped with in-cylinder pressure sensors for continuous combustion monitoring and control, in order to fulfil the more and more strict emission limits. For these reasons, in-cylinder pressure analysis must be carried out with maximum accuracy, in order to minimize the effects of its characteristic…
Sizing of ICE and Lithium-ion battery for series hybrid vehicle over life cycle with battery aging
2013
This paper presents a method to evaluate the volume and weight of the internal combustion engine (ICE) and lithium-ion battery for a series hybrid vehicle that allows to minimize the mean consumption over system life. Individual driving cycles of the car over a total distance of 100 000 km are simulated. The ICE and battery dimensions are approximated; the fuel consumption is evaluated using a general approach. Lithium-ion battery is described including capacity fading and the energy split between ICE and battery system is evaluated using an heuristic approach. Results show a decrease of mean fuel consumption down to 5.1 L/100km.
Simple method of estimating consumption of internal combustion engine for hybrid application
2012
This article presents two simple methods to evaluate the fuel consumption of internal combustion engines. Furthermore, it points out the link between piston volume, engine size and fuel consumption as it gives the possibility to visualize the chosen working points inside an internal combustion engine operation points map. This leads to the fact that this approach is a very helpful tool for the design of hybrid systems including internal combustion engines. The two presented methods, one very simple, one more elaborated, are interesting as first approach of internal combustion engine sizing and to evaluate the consumption of internal combustion engine. The results for six pure internal combu…
An NTC zone compliant knock onset prediction model for spark ignition engines
2015
Abstract Pollutant emissions reduction and energy saving policies increased the production of Spark Ignition (SI) engines operated with gaseous fuels. Natural Gas (NG) and Liquefied Petroleum Gas (LPG), thanks to their low cost and low environmental impact represent the best alternative. Bi-fuel engines, which may run either with gasoline or with gas (NG or LPG), widely spread in many countries thanks to their versatility, high efficiency and low pollutant emissions: gas fueled vehicles, as example, are allowed to run in many limited traffic zones. In the last years, supercharged SI engines fueled with either gasoline or gaseous fuel, spread in the market. Thermodynamic simulations, widely …
Octane Rating of Natural Gas-Gasoline Mixtures on CFR Engine
2014
In the last years new and stricter pollutant emission regulations together with raised cost of conventional fuels resulted in an increased use of gaseous fuels, such as Natural Gas (NG) or Liquefied Petroleum Gas (LPG), for passenger vehicles. Bi-fuel engines represent a transition phase product, allowing to run either with gasoline or with gas, and for this reason are equipped with two separate injection systems. When operating at high loads with gasoline, however, these engines require rich mixtures and retarded combustions in order to prevent from dangerous knocking phenomena: this causes high hydrocarbon (HC) and carbon monoxide (CO) emissions together with high fuel consumption. With t…
A Refined Model for Knock Onset Prediction in Spark Ignition Engines Fueled With Mixtures of Gasoline and Propane
2015
In the last decade, gaseous fuels, such as liquefied petroleum gas (LPG) and natural gas (NG), widely spread in many countries, thanks to their prerogative of low cost and reduced environmental impact. Hence, bi-fuel engines, which allow to run either with gasoline or with gas (LPG or NG), became very popular. Moreover, as experimentally demonstrated by the authors in the previous works, these engines may also be fueled by a mixture of gasoline and gas, which, due to the high knock resistance of gas, allow to use stoichiometric mixtures also at full load, thus drastically improving engine efficiency and pollutant emissions with respect to pure gasoline operation without noticeable power los…
Development and validation of a 5 stroke engine for range extenders application
2014
International audience; A 5-stroke turbo-charged port-injection spark-ignition engine has been developed in the present study for use as a range extender or series-hybrid main power source. The development and the design of the engine are based on 0D/1D model and experimental results have been compared with the engine model. The 5-stroke engine is a three-cylinder in which two cylinders perform a four-stroke cycle and alternatively a second expansion of the burnt gases is performed in the third cylinder. The boost pressure delivered by the turbocharger is controlled by a particular innovative system called “smart wastegate”, different from a conventional wastegate, consisting in a variable …
Steady State Performance of Spark Ignition Engine with Exhaust Energy Recovery
2020
As is known, internal combustion engines based on Otto or Diesel cycles cannot complete the expansion process of the gas inside the cylinder, thus losing a relevant energy content, in the order of 30% of total. The residual energy of the unexpanded gas has been partially exploited through the use of an exhaust gas turbine for turbocharging the internal combustion engine; further attempts have been made with several compound solutions, with an electric generator connected to the turbocharger allowing to convert into electrical energy the quota power produced by the turbine which is not used by the compressor, or with a second turbine downstream the first to increase the exhaust gas energy re…
A Life Cycle Environmental Impact Comparison between Traditional, Hybrid, and Electric Vehicles in the European Context
2021
Global warming (GW) and urban pollution focused a great interest on hybrid electric vehicles (HEVs) and battery electric vehicles (BEVs) as cleaner alternatives to traditional internal combustion engine vehicles (ICEVs). The environmental impact related to the use of both ICEV and HEV mainly depends on the fossil fuel used by the thermal engines, while, in the case of the BEV, depends on the energy sources employed to produce electricity. Moreover, the production phase of each vehicle may also have a relevant environmental impact, due to the manufacturing processes and the materials employed. Starting from these considerations, the authors carried out a fair comparison of the environmental …